Drilling Through Apple AirTags
Apple’s AirTags have taken the world by storm, with their sleek design and innovative features. However, the accompanying keychain accessory can be costly, prompting many to look for alternatives. Enter the intrepid folks at iFixit, who determined that one could drill a hole into the AirTag to attach it to a keychain without the need for the accessory.
The Process
The process of drilling into an AirTag is not for the faint of heart. The key is to drill in a very specific location, as drilling in the wrong spot could cause irreparable damage to the device. Additionally, the hole must be drilled at a specific depth, as going too deep could also cause damage.
Tools Needed
The tools needed to drill into an AirTag are fairly simple. A small drill bit and a drill are the only items required. It is important to note that the drill bit should be small enough to fit into the hole, as a larger bit could cause damage.
Drilling the Hole
Once the tools are gathered, the process of drilling the hole can begin. It is important to take your time and be precise when drilling, as any mistake could cause damage to the device. Additionally, it is important to ensure that the hole is not drilled too deep, as this could also cause damage.
Attaching the AirTag
Once the hole is drilled, the AirTag can be attached to the keychain. This can be done by using a small piece of string or a metal ring. It is important to ensure that the string or ring is securely attached, as this will ensure that the AirTag does not come loose.
Drilling Through Apple AirTags
Recent discussion and media coverage has sparked interest in the possibility of attaching Apple AirTags to a typical key ring without the need for replacing the entire key chain. Apple’s marketing and other sources suggest that the keychain use is the most obvious one for the AirTags. To determine if this is a feasible solution, we will attempt to put a hole in an AirTag.
Gathering the Necessary Materials
The materials needed for this project are a drill, a drill bit, and an AirTag. It is important to note that the drill bit should be smaller than the diameter of the AirTag. This will ensure that the hole is not too large and that the AirTag remains intact.
Drilling the AirTag
Once the materials are gathered, the next step is to begin drilling. It is important to ensure that the drill bit is properly aligned with the AirTag before beginning. Once the drill bit is in place, the drilling process can begin. It is important to take it slowly and to stop periodically to check the progress. The goal is to create a hole that is just large enough for a key ring to fit through.
Drilling Through Apple AirTags
Before attempting to drill through an Apple AirTag, it is important to note that doing so will void any water resistance and IP rating the device may have. As such, it is recommended to only drill through an AirTag if absolutely necessary, and to take the necessary precautions to avoid damaging the device.
Finding the Right Location
Before drilling, it is essential to identify the correct location. This is due to the presence of electronic components inside the AirTag, which could be damaged if the wrong spot is chosen. To find the right location, it is recommended to consult the official Apple website for the exact specifications.
Drilling the Hole
Once the correct location has been identified, the next step is to begin drilling. It is important to use the correct drill bit for the job, as this will ensure the hole is the right size and shape. Additionally, it is important to take care when drilling, as too much pressure could cause the AirTag to crack or break.
Securing the Attachment
Once the hole has been drilled, the next step is to secure the attachment. This can be done using a variety of methods, such as glue, screws, or rivets. It is important to ensure that the attachment is secure, as this will ensure the AirTag remains in place and does not become detached.
Testing the AirTag
It is important to test the AirTag to ensure it is still functioning correctly. This can be done by using the official Apple app to check the AirTag’s connection and functionality. If all is well, the AirTag is now ready to be used.
Marking the Spot
In order to ensure accuracy, it is important to mark the spot where the drill will be inserted. This can be done by placing a dot near the clip mentioned by ifixit. This will ensure that the drill is inserted in the correct location and that the AirTag is not damaged in the process.
Drilling Through the AirTag
Once the spot has been marked, the next step is to drill through the AirTag. This requires a very specific drill bit as there is not much room to maneuver. The drill bit should be small enough to not completely destroy the AirTag while still being able to penetrate the plastic casing. It is important to take extra care while drilling to ensure that the AirTag is not damaged in the process.
Removing the Battery
Once the hole has been drilled, the battery can be removed. This is a relatively straightforward process as the back of the AirTag can be removed easily. However, some people have expressed concern that this makes it too easy for the battery to be removed, potentially by a child.
Drilling Through Apple AirTags
Drilling through Apple AirTags is a relatively straightforward process that requires a few basic tools and materials. The most important of these is a 1/16-inch drill bit, which is necessary to make a clean hole through the AirTag’s casing. Additionally, safety glasses should be worn to protect the eyes from any debris or sparks that may be generated during the drilling process.
Finding the Right Spot
The optimal spot for drilling through an AirTag is located around the seven o’clock position, with the three metallic dots facing upwards. It is important to be as close to the edge of the gray material as possible, as this will ensure a clean and precise hole.
Drilling Through the AirTag
Once the correct spot has been identified, the drill bit should be carefully placed in the desired position. The drill should then be activated, and the bit should be slowly and steadily moved in a circular motion. This will create a clean hole through the AirTag’s casing. After the hole has been created, any excess material should be removed with a cloth or brush.
Drilling Through Apple AirTags
Drilling through Apple AirTags is not recommended, as the plastic casing may not be able to provide the necessary grip on a key ring. To ensure a secure fit, a larger drill bit is needed. Starting at 116 and ending at 564, the drill bit should be used with caution as there is less material on top.
Testing the AirTag
Testing the AirTag is essential to determine if it will stay in place. After inserting the battery and placing the back on, the spot should be carefully examined. If there is enough space over the metal back, a key ring can be attached.
DIY AirTag Keyring
The DIY AirTag Keyring is an alternative to purchasing an AirTag case. Despite initial skepticism, it is possible to put a hole in the tracker. However, caution should be taken as Apple may not be willing to replace any damaged AirTags.
Drilling Through Apple AirTags
Drilling through an Apple AirTag may seem like a daunting task, but with the right tools and a bit of patience, it can be done. The key is to double up the price and the profit margin, as the manufacturing of the AirTag is much less than its retail price. To begin, it is important to ensure that the hole is small enough to remain trapped in the central portion of the key ring. With the right tools, it is possible to make a hole that is small enough to do this.
Testing the Feasibility of Drilling
When drilling through an AirTag, it is important to test the feasibility of the task. Surprisingly, the AirTag is not as fragile as one might expect, and there is enough material left over to grip onto. This means that the task is doable and has some credibility. However, it is important to keep in mind the IP rating of the AirTag, as this will determine how it should be treated.
Alternatives to Drilling
It is possible to purchase Apple’s official key ring for the AirTag, but this is not the only option. It is possible to find third-party key rings on Amazon for a fraction of the price. Alternatively, if one enjoys putting holes in Apple products, then the AirTag is a viable option.
Drilling a hole into an AirTag is a great way to save money on the accompanying keychain accessory. However, it is important to take the necessary precautions to ensure that the hole is drilled in the correct location and at the correct depth. Once the hole is drilled, the AirTag can be securely attached to the keychain.
Drilling through an Apple AirTag is a feasible solution for those who want to attach the device to a key ring without replacing the entire key chain. With the right materials and careful drilling, it is possible to create a hole that is just large enough for a key ring to fit through.
Drilling through an Apple AirTag is a relatively simple process, provided the correct drill bit is used. It is important to take extra care while drilling to ensure that the AirTag is not damaged in the process. Once the hole has been drilled, the battery can be removed easily.
Drilling through an Apple AirTag is a relatively straightforward process that requires a few basic tools and materials. With the correct drill bit and a steady hand, it is possible to create a clean and precise hole through the AirTag’s casing. However, it is important to take the necessary safety precautions when attempting this task.
Drilling through Apple AirTags is not recommended, as the plastic casing may not be able to provide the necessary grip on a key ring. Testing the AirTag is essential to determine if it will stay in place, and the DIY AirTag Keyring is an alternative to purchasing an AirTag case. Caution should be taken when drilling, as Apple may not be willing to replace any damaged AirTags.